Posted by admin | Posted in Parts And Stuff | Posted on 08-12-2011
Tags: car, gps, hardware, ipod, mount
Bracket Kit Ford
 |
 Valley 55140 Base Rail Custom Bracket Kits Ford NIB  US $39.99
|
 BW Turnover Ball Gooseneck Hitch Ford Trucks US $399.00
|
 1316 BW Turnover Ball Gooseneck Hitch Dodge Ram 1500 US $399.00
|
 BW Turnover Ball Gooseneck Hitch All Models US $399.00
|
 BW Companion Combo w Turnoverball 18k 5th Wheel Hitch New Warranty Ford US $1,197.00
|
 Reese Base Rail Mounting Kit for 5th Wheel Hitch New 30035 10 Bolt Kit US $149.00
|
 Reese 30035 5th Wheel Universal Rails w Hardware Kit US $122.16
|
 Reese 58426 Fifth Wheel Bracket Kit for 2004 10 F 150 US $88.83
|
 Torklift FMTARO Ford Chevy Dodge Toyota Nissan rear aftermarket hitch mount US $165.00
|
 Torklift FMTFDRO3 99 04 FORD SD 6 8 BED US $165.00
|
 HAPPIJAC CA FU Multi fit rear bracket kit US $86.00
|
 1000 BW Gooseneck Hitch Chevy GMC C K 8 Bed 1988 1998 US $399.00
|
 1100 BW Gooseneck Hitch Ball Ford F250 F350 1980 1997 US $399.00
|
 1067 BW Gooseneck Hitch Silverado Siera 2500HD 3500HD US $399.00
|
 1108 BW Gooseneck Hitch Ford F250 F350 F450 Super Duty US $399.00
|
 1104 BW Turnover Ball Gooseneck Hitch Ford F150 04 11 US $399.00
|
 BW Companion Combo w Turnoverball 18k 5th Wheel Hitch New Warranty Chevy GMC US $1,197.00
|
 REESE 16K BRACKET KIT 58241 FOR FORD F 150 US $100.00
|
 Firestone W217602520 Ride Rite Rear Kit for Ford US $353.78
|
 Firestone W217602535 Ride Rite Rear Kit for Ford US $353.78
|
Could this engine work for my 1966 Lincoln Continental?
This guy has a Ford 460 Long block and would like to sell me his engines. Would it fit my 66 Continental which has a 462ci V8 engine in it? Its too early to ask my mechanic so hopefully I can run accross one here.
Let me know if it can. Here's the specs
Complete rebuilt ford 460 1)block hot tanked, magna fluxed 2)block bored .30 over, honed w/deck plates sunn 3)new brass freeze plugs 4)new sealed power bearings 5)reconditioned rods 6)decked block, line honed mains. 7)reman heads decked triple angle valve job comes with edelbrock 750 carb. Weiand aluminum intake HEI dist built to run on ford, new water pump, fuel pump, all pulleys and brackets even edelbrock air filter, exhaust manifolds and a engine swap kit to fit this 460 into a foxbody chassis.
If u need anyting else, let me know and I'll ask the guy
Your 462 is a MEL engine and the 460 is a 385 series, so I don't think it will bolt in unless you use the C6 tranny that went to the 460 and make motor mounts and drive-shaft and some other fab work : (
http://www.66lincoln.com/
Originally posted 2010-04-26 10:04:57.
